LM158-N, LM258-N, LM2904-N, LM358-N
www.ti.com
SNOSBT3H –JANUARY 2000–REVISED MARCH 2013
ELECTRICAL CHARACTERISTICS
V
+
= +5.0V, See
(1)
, unless otherwise stated
LM158A LM358A LM158/LM258 Units
Parameter Conditions
Min Typ Max Min Typ Max Min Typ Max
Large Signal Voltage V
+
= 15V, T
A
= 25°C, 50 100 25 100 50 100 V/mV
Gain R
L
≥ 2 kΩ, (For V
O
= 1V to 11V)
Common-Mode T
A
= 25°C,
70 85 65 85 70 85 dB
Rejection Ratio V
CM
= 0V to V
+
−1.5V
Power Supply V
+
= 5V to 30V 65 100 65 100 65 100 dB
Rejection Ratio (LM2904, V
+
= 5V to 26V), T
A
= 25°C
Amplifier-to-Amplifier f = 1 kHz to 20 kHz, T
A
= 25°C (Input
−120 −120 −120 dB
Coupling Referred), See
(2)
Output Current Source V
IN
+
= 1V,
V
IN
−
= 0V,
20 40 20 40 20 40 mA
V
+
= 15V,
V
O
= 2V, T
A
= 25°C
Sink V
IN
−
= 1V, V
IN
+
= 0V
V
+
= 15V, T
A
= 25°C, 10 20 10 20 10 20 mA
V
O
= 2V
V
IN
−
= 1V,
V
IN
+
= 0V
12 50 12 50 12 50 μA
T
A
= 25°C, V
O
= 200 mV,
V
+
= 15V
Short Circuit to Ground T
A
= 25°C, See
(3)
, V
+
= 15V 40 60 40 60 40 60 mA
Input Offset Voltage See
(4)
4 5 7 mV
Input Offset Voltage Drift R
S
= 0Ω 7 15 7 20 7 μV/°C
Input Offset Current I
IN(+)
− I
IN(−)
30 75 100 nA
Input Offset Current Drift R
S
= 0Ω 10 200 10 300 10 pA/°C
Input Bias Current I
IN(+)
or I
IN(−)
40 100 40 200 40 300 nA
Input Common-Mode V
+
= 30 V, See
(5)
(LM2904, V
+
= 26V)
0 V
+
−2 0 V
+
−2 0 V
+
−2 V
Voltage Range
Large Signal Voltage V
+
= +15V
Gain
(V
O
= 1V to 11V) 25 15 25 V/mV
R
L
≥ 2 kΩ
Output V
OH
V
+
= +30V R
L
= 2 kΩ 26 26 26 V
Voltage (LM2904, V
+
= 26V) R
L
= 10 kΩ 27 28 27 28 27 28 V
Swing V
OL
V
+
= 5V, R
L
= 10 kΩ 5 20 5 20 5 20 mV
(1) These specifications are limited to −55°C ≤ T
A
≤ +125°C for the LM158/LM158A. With the LM258/LM258A, all temperature
specifications are limited to −25°C ≤ T
A
≤ +85°C, the LM358/LM358A temperature specifications are limited to 0°C ≤ T
A
≤ +70°C, and
the LM2904 specifications are limited to −40°C ≤ T
A
≤ +85°C.
(2) Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This
typically can be detected as this type of capacitance increases at higher frequencies.
(3) Short circuits from the output to V
+
can cause excessive heating and eventual destruction. When considering short circuits to ground,
the maximum output current is approximately 40 mA independent of the magnitude of V
+
. At values of supply voltage in excess of +15V,
continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result
from simultaneous shorts on all amplifiers.
(4) V
O
≃ 1.4V, R
S
= 0Ω with V
+
from 5V to 30V; and over the full input common-mode range (0V to V
+
−1.5V) at 25°C. For LM2904, V
+
from
5V to 26V.
(5) The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The
upper end of the common-mode voltage range is V
+
−1.5V (at 25°C), but either or both inputs can go to +32V without damage (+26V for
LM2904), independent of the magnitude of V
+
.
Copyright © 2000–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM158-N LM258-N LM2904-N LM358-N
