• 当前位置:
  • 首页
  • >
  • PDF资料
  • >
  • W83877TF PDF文件及第67页内容在线浏览

W83877TF

W83877TF首页预览图
型号: W83877TF
PDF文件:
  • W83877TF PDF文件
  • W83877TF PDF在线浏览
功能描述: WINBOND I/O
PDF文件大小: 968.02 Kbytes
PDF页数: 共154页
制造商: WINBOND[Winbond]
制造商LOGO: WINBOND[Winbond] LOGO
制造商网址: http://www.winbond.com
捡单宝W83877TF
PDF页面索引
120%
W83877TF/W83877TG
-60 -
7.3.15 DMA Transfers
DMA transfers are always to or from the ecpDFifo, tFifo, or CFifo. The DMA uses the standard PC
DMA services. The ECP requests DMA transfers from the host by activating the PDRQ pin. The DMA
will empty or fill the FIFO using the appropriate direction and mode. When the terminal count in the
DMA controller is reached, an interrupt is generated and serviceIntr is asserted, which will disable the
DMA.
7.3.16 Programmed I/O (NON-DMA) Mode
The ECP or parallel port FIFOs can also be operated using interrupt driven programmed I/O.
Programmed I/O transfers are to the ecpDFifo at 400H and ecpAFifo at 000H or from the ecpDFifo
located at 400H, or to/from the tFifo at 400H. The host must set the direction, state, dmaEn = 0 and
serviceIntr = 0 in the programmed I/O transfers.
The ECP requests programmed I/O transfers from the host by activating the IRQ pin. The
programmed I/O will empty or fill the FIFO using the appropriate direction and mode.
7.4 Extension FDD Mode (EXTFDD)
In this mode, the W83877TF/TG changes the printer interface pins to FDC input/output pins, allowing
the user to install a second floppy disk drive (FDD B) through the DB-25 printer connector. The pin
assignments for the FDC input/output pins are shown in Table 8-1.
After the printer interface is set to EXTFDD mode, the following occur:
(1) Pins
MOB and DSB will be forced to inactive state.
(2) Pins
DSKCHG , RDATA , WP , TRAK0 , INDEX will be logically ORed with pins PD4-PD0 to
serve as input signals to the FDC.
(3) Pins PD4-PD0 each will have an internal resistor of about 1K ohm to serve as pull-up resistor for
FDD open drain/collector output.
(4) If the parallel port is set to EXTFDD mode after the system has booted DOS or another operating
system, a warm reset is needed to enable the system to recognize the extension floppy drive.
7.5 Extension 2FDD Mode (EXT2FDD)
In this mode, the W83877TF/TG changes the printer interface pins to FDC input/output pins, allowing
the user to install two external floppy disk drives through the DB-25 printer connector to replace
internal floppy disk drives A and B. The pin assignments for the FDC input/output pins are shown in
Table 8-1.
After the printer interface is set to EXTFDD mode, the following occur:
(1) Pins
MO
A
, DS
A
, MOB, and DSB will be forced to inactive state.
(2) Pins
DSKCHG, RDATA , WP, TRAK0, and INDEX will be logically ORed with pins PD4-PD0 to
serve as input signals to the FDC.
(3) Pins PD4-PD0 each will have an internal resistor of about 1K ohm to serve as pull-up resistor for
FDD open drain/collector output.
(4) If the parallel port is set to EXT2FDD mode after the system has booted DOS or another operating
system, a warm reset is needed to enable the system to recognize the extension floppy drive.
购买、咨询产品请填写询价信息:(3分钟左右您将得到回复)
询价型号*数量*批号封装品牌其它要求
删除
删除
删除
删除
删除
增加行数
  •  公司名:
  • *联系人:
  • *邮箱:
  • *电话:
  •  QQ:
  •  微信:

  • 关注官方微信

  • 联系我们
  • 电话:13714778017
  • 周一至周六:9:00-:18:00
  • 在线客服:

天天IC网由深圳市四方好讯科技有限公司独家运营

天天IC网 ( www.ttic.cc ) 版权所有©2014-2023 粤ICP备15059004号

因腾讯功能限制,可能无法唤起QQ临时会话,(点此复制QQ,添加好友),建议您使用TT在线询价。

继续唤起QQ 打开TT询价