• 当前位置:
  • 首页
  • >
  • PDF资料
  • >
  • W83877TF PDF文件及第65页内容在线浏览

W83877TF

W83877TF首页预览图
型号: W83877TF
PDF文件:
  • W83877TF PDF文件
  • W83877TF PDF在线浏览
功能描述: WINBOND I/O
PDF文件大小: 968.02 Kbytes
PDF页数: 共154页
制造商: WINBOND[Winbond]
制造商LOGO: WINBOND[Winbond] LOGO
制造商网址: http://www.winbond.com
捡单宝W83877TF
PDF页面索引
120%
W83877TF/W83877TG
-58 -
7.3.12 ECP Pin Descriptions
NAME TYPE DESCRIPTION
nStrobe (HostClk) O The nStrobe registers data or address into the slave on the
asserting edge during write operations. This signal
handshakes with Busy.
PD<7:0> I/O These signals contains address or data or RLE data.
nAck (PeriphClk) I This signal indicates valid data driven by the peripheral when
asserted. This signal handshakes with nAutofd in reverse.
Busy (PeriphAck) I This signal desserts to indicate that the peripheral can accept
data. It indicates whether the data lines contain ECP
command information or data in the reverse direction. When in
reverse direction, normal data are transferred when Busy
(PeriphAck) is high and an 8-bit command is transferred when
it is low.
PError (nAckReverse) I This signal is used to acknowledge a change in the direction
of the transfer (asserted = forward). The peripheral drives this
signal low to acknowledge nReverseRequest. The host relies
upon nAckReverse to determine when it is permitted to drive
the data bus.
Select (Xflag) I Indicates printer on line.
nAutoFd (HostAck) O Requests a byte of data from the peripheral when it is
asserted. This signal indicates whether the data lines contain
ECP address or data in the forward direction. When in forward
direction, normal data are transferred when nAutoFd
(HostAck) is high and an 8-bit command is transferred when it
is low.
nFault (nPeriphRequest) I Generates an error interrupt when it is asserted. This signal is
valid only in the forward direction. The peripheral is permitted
(but not required) to drive this pin low to request a reverse
transfer during ECP Mode.
nInit (nReverseRequest) O This signal sets the transfer direction (asserted = reverse,
deasserted = forward). This pin is driven low to place the
channel in the reverse direction.
nSelectIn (ECPMode) O This signal is always deasserted in ECP mode.
购买、咨询产品请填写询价信息:(3分钟左右您将得到回复)
询价型号*数量*批号封装品牌其它要求
删除
删除
删除
删除
删除
增加行数
  •  公司名:
  • *联系人:
  • *邮箱:
  • *电话:
  •  QQ:
  •  微信:

  • 关注官方微信

  • 联系我们
  • 电话:13714778017
  • 周一至周六:9:00-:18:00
  • 在线客服:

天天IC网由深圳市四方好讯科技有限公司独家运营

天天IC网 ( www.ttic.cc ) 版权所有©2014-2023 粤ICP备15059004号

因腾讯功能限制,可能无法唤起QQ临时会话,(点此复制QQ,添加好友),建议您使用TT在线询价。

继续唤起QQ 打开TT询价