• 当前位置:
  • 首页
  • >
  • PDF资料
  • >
  • W78LE516P-24 PDF文件及第5页内容在线浏览

W78LE516P-24

W78LE516P-24首页预览图
型号: W78LE516P-24
PDF文件:
  • W78LE516P-24 PDF文件
  • W78LE516P-24 PDF在线浏览
功能描述: 8-BIT MICROCONTROLLER
PDF文件大小: 287.33 Kbytes
PDF页数: 共31页
制造商: WINBOND[Winbond]
制造商LOGO: WINBOND[Winbond] LOGO
制造商网址: http://www.winbond.com
捡单宝W78LE516P-24
PDF页面索引
120%
Preliminary W78LE516
Publication Release Date: June 2000
- 5 - Revision A1
RAM 80H
FFH can only be addressed indirectly as the same as in 8051. Address pointers are R0,
R1 of the selected registers bank.
AUX-RAM 0HFFH is addressed indirectly as the same way to access external data memory with
the MOVX instruction. Address pointer are R0 and R1 of the selected register bank and DPTR
register. An access to external data memory locations higher than FFH will be performed with the
MOVX instruction in the same way as in the 8051. The AUX-RAM is disable after a reset. Setting
the bit 4 in CHPCON register will enable the access to AUX-RAM. When AUX-RAM is enabled the
instructions of "MOVX @Ri" will always access to on-chip AUX-RAM. When executing from internal
program memory, an access to AUX-RAM will not affect the Ports P0, P2,
WR
and
RD
.
Example,
CHPENR REG F6H
CHPCON REG BFH
MOV CHPENR,#87H
MOV CHPENR,#59H
ORL CHPCON,#00010000B ; enable AUX-RAM
MOV CHPENR,#00H
MOV R0,#12H
MOV A,#34H
MOVX @R0,A ; Write 34h data to 12h address.
Timers 0, 1, and 2
Timers 0, 1, and 2 each consist of two 8-bit data registers. These are called TL0 and TH0 for Timer
0, TL1 and TH1 for Timer 1, and TL2 and TH2 for Timer 2. The TCON and TMOD registers provide
control functions for timers 0, 1. The T2CON register provides control functions for Timer 2. RCAP2H
and RCAP2L are used as reload/capture registers for Timer 2. The operations of Timer 0 and Timer
1 are the same as in the W78C51. Timer 2 is a 16-bit timer/counter that is configured and controlled
by the T2CON register. Like Timers 0 and 1, Timer 2 can operate as either an external event counter
or as an internal timer, depending on the setting of bit C/T2 in T2CON. Timer 2 has three operating
modes: capture, auto-reload, and baud rate generator. The clock speed at capture or auto-reload
mode is the same as that of Timers 0 and 1.
Clock
The W78LE516 is designed with either a crystal oscillator or an external clock. Internally, the clock is
divided by two before it is used by default. This makes the W78LE516 relatively insensitive to duty
cycle variations in the clock.
Crystal Oscillator
The W78LE516 incorporates a built-in crystal oscillator. To make the oscillator work, a crystal must
be connected across pins XTAL1 and XTAL2. In addition, a load capacitor must be connected from
each pin to ground.
External Clock
An external clock should be connected to pin XTAL1. Pin XTAL2 should be left unconnected. The
XTAL1 input is a CMOS-type input, as required by the crystal oscillator.
购买、咨询产品请填写询价信息:(3分钟左右您将得到回复)
询价型号*数量*批号封装品牌其它要求
删除
删除
删除
删除
删除
增加行数
  •  公司名:
  • *联系人:
  • *邮箱:
  • *电话:
  •  QQ:
  •  微信:

  • 关注官方微信

  • 联系我们
  • 电话:13714778017
  • 周一至周六:9:00-:18:00
  • 在线客服:

天天IC网由深圳市四方好讯科技有限公司独家运营

天天IC网 ( www.ttic.cc ) 版权所有©2014-2023 粤ICP备15059004号

因腾讯功能限制,可能无法唤起QQ临时会话,(点此复制QQ,添加好友),建议您使用TT在线询价。

继续唤起QQ 打开TT询价