• 当前位置:
  • 首页
  • >
  • PDF资料
  • >
  • LT1952EGN PDF文件及第17页内容在线浏览

LT1952EGN

LT1952EGN首页预览图
型号: LT1952EGN
PDF文件:
  • LT1952EGN PDF文件
  • LT1952EGN PDF在线浏览
功能描述: Single Switch Synchronous Forward Controller
PDF文件大小: 252.83 Kbytes
PDF页数: 共24页
制造商: LINER[Linear Technology]
制造商LOGO: LINER[Linear Technology] LOGO
制造商网址: http://www.linear.com
捡单宝LT1952EGN
PDF页面索引
120%
LT1952
17
1952f
APPLICATIO S I FOR ATIO
WUU
U
Soft-start latch reset requires all of the following:
(A) V
IN
> 14.25*, and
(B) SD_V
SEC
> 1.32V, and
(C) OC < 100mV, and
(D) SS_MAXDC < 0.45V (SS_MAXDC reset threshold)
*V
IN
> 8.75V is ok for latch reset if the latch was only set
by over-current condition in (3) above
SS_MAXDC Discharge Timing
It can be seen in Figure 10 that two types of discharge can
occur for the SS_MAXDC pin. In timing (A) the fault that
caused the soft-start event has been removed before
SS_MAXDC falls to 0.45V. This means the soft-start latch
will be reset when SS_MAXDC falls to 0.45V and
SS_MAXDC will begin charging. In timing (B), the fault
that caused the soft-start event is not removed until some
time after SS_MAXDC has fallen past 0.45V. The
SS_MAXDC pin continues to discharge to 0.2V and re-
mains low until all faults are removed.
The time for SS_MAXDC to fall to a given voltage can be
approximated as,
SS_MAXDC (t
FALL
) =
(C
SS
/I
DIS
) • [SS_MAXDC(DC) – V
SS(MIN)
]
where,
I
DIS
= net discharge current on C
SS
C
SS
= capacitor value at SS_MAXDC pin
SS_MAXDC(DC) = programmed DC voltage
V
SS(MIN)
= minimum SS_MAXDC voltage before
recharge
I
DIS
~ 8e
–4
+ (V
REF
– V
SS(MIN)
)[(1/2R
B
) – (1/R
T
)]
For faults arising from (1) and (2),
V
REF
= 100mV.
For a fault arising from (3),
V
REF
= 2.5V.
SS_MAXDC(DC) = V
REF
[R
B
/(R
T
+ R
B
)]
V
SS(MIN)
= SS_MAXDC reset threshold = 0.45V
(if fault removed before t
FALL
)
Example
For an over-current fault (OC > 100mV), V
REF
= 2.5V,
R
T
= 35.7k, R
B
= 100k, C
SS
= 0.1µF and assume
V
SS(MIN)
= 0.45V,
I
DIS
~ 8e
–4
+ (2.5 – 0.45)[(1/2 • 100k) – (1/35.7k)]
= 8e
–4
+ (2.05)(–0.23e
–4
) = 7.5e
–4
SS_MAXDC(DC) = 1.84V
SS_MAXDC (t
FALL
) = (1e – 7/7.5e
–4
) • (1.84 – 0.45)
= 1.85e
–4
s
If the OC fault is not removed before 185µs then SS_MAXDC
will continue to fall past 0.45V towards a new V
SS(MIN)
.
The typical V
OL
for SS_MAXDC at 150µA is 0.2V.
SS_MAXDC Charge Timing
When all faults are removed and the SS_MAXDC pin has
fallen to its reset threshold of 0.45V or lower, the
SS_MAXDC pin will be released and allowed to charge.
SS_MAXDC will rise until it settles at its programmed DC
voltage — setting the maximum switch duty cycle clamp.
The calculation of charging time for the SS_MAXDC pin
between any two voltage levels can be approximated as an
RC charging waveform using the model shown in
Figure 11.
The ability to predict SS_MAXDC rise time between any
two voltages allows prediction of several key timing
periods:
(1) No Switching Period
(time from SS_MAXDC(DC) to V
SS(MIN)
+ time from
V
SS(MIN)
to V
SS(ACTIVE)
)
(2) Converter Output Rise Time
(time from V
SS(ACTIVE)
to V
SS(REG)
; V
SS(REG)
is the
level of SS_MAXDC where maximum duty cycle
clamp equals the natural duty cycle of the switch)
(3) Time For Maximum Duty Cycle Clamp within X% of
Target Value
The time for SS_MAXDC to charge to a given voltage V
SS
is found by re-arranging,
V
SS
(t) = SS_MAXDC(DC) (1 – e
(–t/RC)
)
购买、咨询产品请填写询价信息:(3分钟左右您将得到回复)
询价型号*数量*批号封装品牌其它要求
删除
删除
删除
删除
删除
增加行数
  •  公司名:
  • *联系人:
  • *邮箱:
  • *电话:
  •  QQ:
  •  微信:

  • 关注官方微信

  • 联系我们
  • 电话:13714778017
  • 周一至周六:9:00-:18:00
  • 在线客服:

天天IC网由深圳市四方好讯科技有限公司独家运营

天天IC网 ( www.ttic.cc ) 版权所有©2014-2023 粤ICP备15059004号

因腾讯功能限制,可能无法唤起QQ临时会话,(点此复制QQ,添加好友),建议您使用TT在线询价。

继续唤起QQ 打开TT询价