• 当前位置:
  • 首页
  • >
  • PDF资料
  • >
  • LM5005MHX PDF文件及第20页内容在线浏览

LM5005MHX

LM5005MHX首页预览图
型号: LM5005MHX
PDF文件:
  • LM5005MHX PDF文件
  • LM5005MHX PDF在线浏览
功能描述: LM5005 High Voltage 2.5 Amp Buck Regulator
PDF文件大小: 947.25 Kbytes
PDF页数: 共28页
制造商: TI[Texas Instruments]
制造商LOGO: TI[Texas Instruments] LOGO
制造商网址: http://www.ti.com
捡单宝LM5005MHX
PDF页面索引
120%
LM5005
SNVS397D SEPTEMBER 2005REVISED MARCH 2013
www.ti.com
PWB BOARD LAYOUT AND THERMAL CONSIDERATIONS
The circuit in Figure 9 serves as both a block diagram of the LM5005 and a typical application board schematic
for the LM5005. In a buck regulator there are two loops where currents are switched very fast. The first loop
starts from the input capacitors, to the regulator VIN pin, to the regulator SW pin, to the inductor then out to the
load. The second loop starts from the output capacitor ground, to the regulator PGND pins, to the regulator IS
pins, to the diode anode, to the inductor and then out to the load. Minimizing the loop area of these two loops
reduces the stray inductance and minimizes noise and possible erratic operation. A ground plane in the PC
board is recommended as a means to connect the input filter capacitors to the output filter capacitors and the
PGND pins of the regulator. Connect all of the low power ground connections (C
SS
, R
T
, C
RAMP
) directly to the
regulator AGND pin. Connect the AGND and PGND pins together through the topside copper area covering the
entire underside of the device. Place several vias in this underside copper area to the ground plane.
The two highest power dissipating components are the re-circulating diode and the LM5005 regulator IC. The
easiest method to determine the power dissipated within the LM5005 is to measure the total conversion losses
(Pin Pout) then subtract the power losses in the Schottky diode, output inductor and snubber resistor. An
approximation for the Schottky diode loss is P = (1-D) x Iout x Vfwd. An approximation for the output inductor
power is P = I
OUT
2
x R x 1.1, where R is the DC resistance of the inductor and the 1.1 factor is an approximation
for the ac losses. If a snubber is used, the power loss can be estimated with an oscilloscope by observation of
the resistor voltage drop at both turn-on and turn-off transitions. The regulator has an exposed thermal pad to aid
power dissipation. Adding several vias under the device to the ground plane will greatly reduce the regulator
junction temperature. Selecting a diode with an exposed pad will aid the power dissipation of the diode.
Table 1. 5V, 2.5A Demo Board Bill of Materials
ITEM PART NUMBER DESCRIPTION VALUE
C 1 C4532X7R2A225M CAPACITOR, CER, TDK 2.2µ, 100V
C 2 C4532X7R2A225M CAPACITOR, CER, TDK 2.2µ, 100V
C 3 C0805C331G1GAC CAPACITOR, CER, KEMET 330p, 100V
C 4 C2012X7R2A103K CAPACITOR, CER, TDK 0.01µ, 100V
C 5 C2012X7R2A103K CAPACITOR, CER, TDK 0.01µ, 100V
C 6 OPEN NOT USED
C 7 C2012X7R2A223K CAPACITOR, CER, TDK 0.022µ, 100V
C 8 C2012X7R1C474M CAPACITOR, CER, TDK 0.47µ, 16V
C 9 C3225X7R1C226M CAPACITOR, CER, TDK 22µ, 16V
C 10 EEFHE0J151R CAPACITOR, SP, PANASINIC 150µ, 6.3V
C 11 C0805C331G1GAC CAPACITOR, CER, KEMET 330p, 100V
C 12 OPEN NOT USED
D 1 CSHD6-100C DIODE, 100V, CENTRAL
6CWQ10FN DIODE, 100V, IR (D1-ALT)
L 1 DR127-330 INDUCTOR, COOPER 33µH
R 1 OPEN NOT USED
R 2 OPEN NOT USED
R 3 CRCW08052102F RESISTOR 21K
R 4 CRCW08054992F RESISTOR 49.9K
R 5 CRCW08055111F RESISTOR 5.11K
R 6 CRCW08051651F RESISTOR 1.65K
R 7 CRCW2512100J RESISTOR 10, 1W
U 1 LM5005 REGULATOR, TEXAS INSTRUMENTS
20 Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM5005
购买、咨询产品请填写询价信息:(3分钟左右您将得到回复)
询价型号*数量*批号封装品牌其它要求
删除
删除
删除
删除
删除
增加行数
  •  公司名:
  • *联系人:
  • *邮箱:
  • *电话:
  •  QQ:
  •  微信:

  • 关注官方微信

  • 联系我们
  • 电话:13714778017
  • 周一至周六:9:00-:18:00
  • 在线客服:

天天IC网由深圳市四方好讯科技有限公司独家运营

天天IC网 ( www.ttic.cc ) 版权所有©2014-2023 粤ICP备15059004号

因腾讯功能限制,可能无法唤起QQ临时会话,(点此复制QQ,添加好友),建议您使用TT在线询价。

继续唤起QQ 打开TT询价