• 当前位置:
  • 首页
  • >
  • PDF资料
  • >
  • LM3S8530-IQR80-C1 PDF文件及第48页内容在线浏览

LM3S8530-IQR80-C1

LM3S8530-IQR80-C1首页预览图
型号: LM3S8530-IQR80-C1
PDF文件:
  • LM3S8530-IQR80-C1 PDF文件
  • LM3S8530-IQR80-C1 PDF在线浏览
功能描述: Stellaris® LM3S8530 Microcontroller
PDF文件大小: 4249.13 Kbytes
PDF页数: 共526页
制造商: TI[Texas Instruments]
制造商LOGO: TI[Texas Instruments] LOGO
制造商网址: http://www.ti.com
捡单宝LM3S8530-IQR80-C1
PDF页面索引
[1] 页[2] 页[3] 页[4] 页[5] 页[6] 页[7] 页[8] 页[9] 页[10] 页[11] 页[12] 页[13] 页[14] 页[15] 页[16] 页[17] 页[18] 页[19] 页[20] 页[21] 页[22] 页[23] 页[24] 页[25] 页[26] 页[27] 页[28] 页[29] 页[30] 页[31] 页[32] 页[33] 页[34] 页[35] 页[36] 页[37] 页[38] 页[39] 页[40] 页[41] 页[42] 页[43] 页[44] 页[45] 页[46] 页[47] 页[48] 页[49] 页[50] 页[51] 页[52] 页[53] 页[54] 页[55] 页[56] 页[57] 页[58] 页[59] 页[60] 页[61] 页[62] 页[63] 页[64] 页[65] 页[66] 页[67] 页[68] 页[69] 页[70] 页[71] 页[72] 页[73] 页[74] 页[75] 页[76] 页[77] 页[78] 页[79] 页[80] 页[81] 页[82] 页[83] 页[84] 页[85] 页[86] 页[87] 页[88] 页[89] 页[90] 页[91] 页[92] 页[93] 页[94] 页[95] 页[96] 页[97] 页[98] 页[99] 页[100] 页[101] 页[102] 页[103] 页[104] 页[105] 页[106] 页[107] 页[108] 页[109] 页[110] 页[111] 页[112] 页[113] 页[114] 页[115] 页[116] 页[117] 页[118] 页[119] 页[120] 页[121] 页[122] 页[123] 页[124] 页[125] 页[126] 页[127] 页[128] 页[129] 页[130] 页[131] 页[132] 页[133] 页[134] 页[135] 页[136] 页[137] 页[138] 页[139] 页[140] 页[141] 页[142] 页[143] 页[144] 页[145] 页[146] 页[147] 页[148] 页[149] 页[150] 页[151] 页[152] 页[153] 页[154] 页[155] 页[156] 页[157] 页[158] 页[159] 页[160] 页[161] 页[162] 页[163] 页[164] 页[165] 页[166] 页[167] 页[168] 页[169] 页[170] 页[171] 页[172] 页[173] 页[174] 页[175] 页[176] 页[177] 页[178] 页[179] 页[180] 页[181] 页[182] 页[183] 页[184] 页[185] 页[186] 页[187] 页[188] 页[189] 页[190] 页[191] 页[192] 页[193] 页[194] 页[195] 页[196] 页[197] 页[198] 页[199] 页[200] 页[201] 页[202] 页[203] 页[204] 页[205] 页[206] 页[207] 页[208] 页[209] 页[210] 页[211] 页[212] 页[213] 页[214] 页[215] 页[216] 页[217] 页[218] 页[219] 页[220] 页[221] 页[222] 页[223] 页[224] 页[225] 页[226] 页[227] 页[228] 页[229] 页[230] 页[231] 页[232] 页[233] 页[234] 页[235] 页[236] 页[237] 页[238] 页[239] 页[240] 页[241] 页[242] 页[243] 页[244] 页[245] 页[246] 页[247] 页[248] 页[249] 页[250] 页[251] 页[252] 页[253] 页[254] 页[255] 页[256] 页[257] 页[258] 页[259] 页[260] 页[261] 页[262] 页[263] 页[264] 页[265] 页[266] 页[267] 页[268] 页[269] 页[270] 页[271] 页[272] 页[273] 页[274] 页[275] 页[276] 页[277] 页[278] 页[279] 页[280] 页[281] 页[282] 页[283] 页[284] 页[285] 页[286] 页[287] 页[288] 页[289] 页[290] 页[291] 页[292] 页[293] 页[294] 页[295] 页[296] 页[297] 页[298] 页[299] 页[300] 页[301] 页[302] 页[303] 页[304] 页[305] 页[306] 页[307] 页[308] 页[309] 页[310] 页[311] 页[312] 页[313] 页[314] 页[315] 页[316] 页[317] 页[318] 页[319] 页[320] 页[321] 页[322] 页[323] 页[324] 页[325] 页[326] 页[327] 页[328] 页[329] 页[330] 页[331] 页[332] 页[333] 页[334] 页[335] 页[336] 页[337] 页[338] 页[339] 页[340] 页[341] 页[342] 页[343] 页[344] 页[345] 页[346] 页[347] 页[348] 页[349] 页[350] 页[351] 页[352] 页[353] 页[354] 页[355] 页[356] 页[357] 页[358] 页[359] 页[360] 页[361] 页[362] 页[363] 页[364] 页[365] 页[366] 页[367] 页[368] 页[369] 页[370] 页[371] 页[372] 页[373] 页[374] 页[375] 页[376] 页[377] 页[378] 页[379] 页[380] 页[381] 页[382] 页[383] 页[384] 页[385] 页[386] 页[387] 页[388] 页[389] 页[390] 页[391] 页[392] 页[393] 页[394] 页[395] 页[396] 页[397] 页[398] 页[399] 页[400] 页[401] 页[402] 页[403] 页[404] 页[405] 页[406] 页[407] 页[408] 页[409] 页[410] 页[411] 页[412] 页[413] 页[414] 页[415] 页[416] 页[417] 页[418] 页[419] 页[420] 页[421] 页[422] 页[423] 页[424] 页[425] 页[426] 页[427] 页[428] 页[429] 页[430] 页[431] 页[432] 页[433] 页[434] 页[435] 页[436] 页[437] 页[438] 页[439] 页[440] 页[441] 页[442] 页[443] 页[444] 页[445] 页[446] 页[447] 页[448] 页[449] 页[450] 页[451] 页[452] 页[453] 页[454] 页[455] 页[456] 页[457] 页[458] 页[459] 页[460] 页[461] 页[462] 页[463] 页[464] 页[465] 页[466] 页[467] 页[468] 页[469] 页[470] 页[471] 页[472] 页[473] 页[474] 页[475] 页[476] 页[477] 页[478] 页[479] 页[480] 页[481] 页[482] 页[483] 页[484] 页[485] 页[486] 页[487] 页[488] 页[489] 页[490] 页[491] 页[492] 页[493] 页[494] 页[495] 页[496] 页[497] 页[498] 页[499] 页[500] 页[501] 页[502] 页[503] 页[504] 页[505] 页[506] 页[507] 页[508] 页[509] 页[510] 页[511] 页[512] 页[513] 页[514] 页[515] 页[516] 页[517] 页[518] 页[519] 页[520] 页[521] 页[522] 页[523] 页[524] 页[525] 页[526] 页
120%
4 Interrupts
The ARM Cortex-M3 processor and the Nested Vectored Interrupt Controller (NVIC) prioritize and
handle all exceptions. All exceptions are handled in Handler Mode. The processor state is
automatically stored to the stack on an exception, and automatically restored from the stack at the
end of the Interrupt Service Routine (ISR). The vector is fetched in parallel to the state saving, which
enables efficient interrupt entry. The processor supports tail-chaining, which enables back-to-back
interrupts to be performed without the overhead of state saving and restoration.
Table 4-1 on page 48 lists all exception types. Software can set eight priority levels on seven of
these exceptions (system handlers) as well as on 26 interrupts (listed in Table 4-2 on page 49).
Priorities on the system handlers are set with the NVIC System Handler Priority registers. Interrupts
are enabled through the NVIC Interrupt Set Enable register and prioritized with the NVIC Interrupt
Priority registers. You also can group priorities by splitting priority levels into pre-emption priorities
and subpriorities. All of the interrupt registers are described in Chapter 8, “Nested Vectored Interrupt
Controller” in the ARM® Cortex™-M3 Technical Reference Manual.
Internally, the highest user-settable priority (0) is treated as fourth priority, after a Reset, NMI, and
a Hard Fault. Note that 0 is the default priority for all the settable priorities.
If you assign the same priority level to two or more interrupts, their hardware priority (the lower
position number) determines the order in which the processor activates them. For example, if both
GPIO Port A and GPIO Port B are priority level 1, then GPIO Port A has higher priority.
Important: It may take several processor cycles after a write to clear an interrupt source in order
for NVIC to see the interrupt source de-assert. This means if the interrupt clear is done
as the last action in an interrupt handler, it is possible for the interrupt handler to complete
while NVIC sees the interrupt as still asserted, causing the interrupt handler to be
re-entered errantly. This can be avoided by either clearing the interrupt source at the
beginning of the interrupt handler or by performing a read or write after the write to clear
the interrupt source (and flush the write buffer).
See Chapter 5, “Exceptions” and Chapter 8, “Nested Vectored Interrupt Controller” in the ARM®
Cortex™-M3 Technical Reference Manual for more information on exceptions and interrupts.
Table 4-1. Exception Types
DescriptionPriority
a
Vector
Number
Exception Type
Stack top is loaded from first entry of vector table on reset.-0-
Invoked on power up and warm reset. On first instruction, drops to
lowest priority (and then is called the base level of activation). This is
asynchronous.
-3 (highest)1Reset
Cannot be stopped or preempted by any exception but reset. This is
asynchronous.
An NMI is only producible by software, using the NVIC Interrupt
Control State register.
-22Non-Maskable
Interrupt (NMI)
All classes of Fault, when the fault cannot activate due to priority or
the configurable fault handler has been disabled. This is synchronous.
-13Hard Fault
MPU mismatch, including access violation and no match. This is
synchronous.
The priority of this exception can be changed.
settable4Memory Management
June 22, 201048
Texas Instruments-Production Data
Interrupts
购买、咨询产品请填写询价信息:(3分钟左右您将得到回复)
询价型号*数量*批号封装品牌其它要求
删除
删除
删除
删除
删除
增加行数
  •  公司名:
  • *联系人:
  • *邮箱:
  • *电话:
  •  QQ:
  •  微信:

  • 关注官方微信

  • 联系我们
  • 电话:13714778017
  • 周一至周六:9:00-:18:00
  • 在线客服:

天天IC网由深圳市四方好讯科技有限公司独家运营

天天IC网 ( www.ttic.cc ) 版权所有©2014-2023 粤ICP备15059004号

因腾讯功能限制,可能无法唤起QQ临时会话,(点此复制QQ,添加好友),建议您使用TT在线询价。

继续唤起QQ 打开TT询价