• 当前位置:
  • 首页
  • >
  • PDF资料
  • >
  • LM3S610-IQN50 PDF文件及第234页内容在线浏览

LM3S610-IQN50

LM3S610-IQN50首页预览图
型号: LM3S610-IQN50
PDF文件:
  • LM3S610-IQN50 PDF文件
  • LM3S610-IQN50 PDF在线浏览
功能描述: Microcontroller
PDF文件大小: 2341.71 Kbytes
PDF页数: 共396页
制造商: ETC2[List of Unclassifed Manufacturers]
制造商LOGO: ETC2[List of Unclassifed Manufacturers] LOGO
制造商网址:
捡单宝LM3S610-IQN50
PDF页面索引
[1] 页[2] 页[3] 页[4] 页[5] 页[6] 页[7] 页[8] 页[9] 页[10] 页[11] 页[12] 页[13] 页[14] 页[15] 页[16] 页[17] 页[18] 页[19] 页[20] 页[21] 页[22] 页[23] 页[24] 页[25] 页[26] 页[27] 页[28] 页[29] 页[30] 页[31] 页[32] 页[33] 页[34] 页[35] 页[36] 页[37] 页[38] 页[39] 页[40] 页[41] 页[42] 页[43] 页[44] 页[45] 页[46] 页[47] 页[48] 页[49] 页[50] 页[51] 页[52] 页[53] 页[54] 页[55] 页[56] 页[57] 页[58] 页[59] 页[60] 页[61] 页[62] 页[63] 页[64] 页[65] 页[66] 页[67] 页[68] 页[69] 页[70] 页[71] 页[72] 页[73] 页[74] 页[75] 页[76] 页[77] 页[78] 页[79] 页[80] 页[81] 页[82] 页[83] 页[84] 页[85] 页[86] 页[87] 页[88] 页[89] 页[90] 页[91] 页[92] 页[93] 页[94] 页[95] 页[96] 页[97] 页[98] 页[99] 页[100] 页[101] 页[102] 页[103] 页[104] 页[105] 页[106] 页[107] 页[108] 页[109] 页[110] 页[111] 页[112] 页[113] 页[114] 页[115] 页[116] 页[117] 页[118] 页[119] 页[120] 页[121] 页[122] 页[123] 页[124] 页[125] 页[126] 页[127] 页[128] 页[129] 页[130] 页[131] 页[132] 页[133] 页[134] 页[135] 页[136] 页[137] 页[138] 页[139] 页[140] 页[141] 页[142] 页[143] 页[144] 页[145] 页[146] 页[147] 页[148] 页[149] 页[150] 页[151] 页[152] 页[153] 页[154] 页[155] 页[156] 页[157] 页[158] 页[159] 页[160] 页[161] 页[162] 页[163] 页[164] 页[165] 页[166] 页[167] 页[168] 页[169] 页[170] 页[171] 页[172] 页[173] 页[174] 页[175] 页[176] 页[177] 页[178] 页[179] 页[180] 页[181] 页[182] 页[183] 页[184] 页[185] 页[186] 页[187] 页[188] 页[189] 页[190] 页[191] 页[192] 页[193] 页[194] 页[195] 页[196] 页[197] 页[198] 页[199] 页[200] 页[201] 页[202] 页[203] 页[204] 页[205] 页[206] 页[207] 页[208] 页[209] 页[210] 页[211] 页[212] 页[213] 页[214] 页[215] 页[216] 页[217] 页[218] 页[219] 页[220] 页[221] 页[222] 页[223] 页[224] 页[225] 页[226] 页[227] 页[228] 页[229] 页[230] 页[231] 页[232] 页[233] 页[234] 页[235] 页[236] 页[237] 页[238] 页[239] 页[240] 页[241] 页[242] 页[243] 页[244] 页[245] 页[246] 页[247] 页[248] 页[249] 页[250] 页[251] 页[252] 页[253] 页[254] 页[255] 页[256] 页[257] 页[258] 页[259] 页[260] 页[261] 页[262] 页[263] 页[264] 页[265] 页[266] 页[267] 页[268] 页[269] 页[270] 页[271] 页[272] 页[273] 页[274] 页[275] 页[276] 页[277] 页[278] 页[279] 页[280] 页[281] 页[282] 页[283] 页[284] 页[285] 页[286] 页[287] 页[288] 页[289] 页[290] 页[291] 页[292] 页[293] 页[294] 页[295] 页[296] 页[297] 页[298] 页[299] 页[300] 页[301] 页[302] 页[303] 页[304] 页[305] 页[306] 页[307] 页[308] 页[309] 页[310] 页[311] 页[312] 页[313] 页[314] 页[315] 页[316] 页[317] 页[318] 页[319] 页[320] 页[321] 页[322] 页[323] 页[324] 页[325] 页[326] 页[327] 页[328] 页[329] 页[330] 页[331] 页[332] 页[333] 页[334] 页[335] 页[336] 页[337] 页[338] 页[339] 页[340] 页[341] 页[342] 页[343] 页[344] 页[345] 页[346] 页[347] 页[348] 页[349] 页[350] 页[351] 页[352] 页[353] 页[354] 页[355] 页[356] 页[357] 页[358] 页[359] 页[360] 页[361] 页[362] 页[363] 页[364] 页[365] 页[366] 页[367] 页[368] 页[369] 页[370] 页[371] 页[372] 页[373] 页[374] 页[375] 页[376] 页[377] 页[378] 页[379] 页[380] 页[381] 页[382] 页[383] 页[384] 页[385] 页[386] 页[387] 页[388] 页[389] 页[390] 页[391] 页[392] 页[393] 页[394] 页[395] 页[396] 页
120%
Universal Asynchronous Receivers/Transmitters (UARTs)
234 October 8, 2006
Preliminary
Receive Timeout
Transmit (when condition defined in the TXIFLSEL bit in the UARTIFLS register is met)
Receive (when condition defined in the RXIFLSEL bit in the UARTIFLS register is met)
All of the interrupt events are ORed together before being sent to the interrupt controller, so the
UART can only generate a single interrupt request to the controller at any given time. Software can
service multiple interrupt events in a single interrupt service routine by reading the UART Masked
Interrupt Status (UARTMIS) register (see page 252).
The interrupt events that can trigger a controller-level interrupt are defined in the UART Interrupt
Mask (UARTIM) register (see page 249) by setting the corresponding IM bit to 1. If interrupts are
not used, the raw interrupt status is always visible via the UART Raw Interrupt St atus (UARTRIS)
registe r (see page 251).
Interrupts are always cleared (for both the UARTMIS and UARTRIS registers) by setting the
corresponding bit in the UART Interrupt Clear (UARTICR) register (see page 253).
12.2.6 Loopback Operation
The UART can be placed into an internal loopback mode for diagnostic or debug work. This is
accomplished by setting the LBE bit in the UARTCTL register (see page 247). In loopback mode,
data transmitted on U0Tx is received on the U0Rx input, and data transmitted on U1Tx is received
on the U1Rx input.
12.3 Initialization and Configuration
To use the UARTs, the peripheral clock must be enabled by setting the UART0 or UART1 bits in the
RCGC1 register.
This section discusses the steps that are required for using a UART module. For this example, the
system clock is assumed to be 20 MHz and the desired UART configuration is:
115 200 bau d rate
Data length of 8 bits
One stop bit
No parity
FIFOs disabled
No interrupts
The first thing to consider when programming the UART is the baud-rate divisor (BRD), since the
UARTIBRD and UARTFBRD registers must be written before the UARTLCRH register. Using the
equation described in “Baud-Rate Generation” on page 232, the BRD can be calculated:
BRD = 20,000,000 / (16 * 115,200) = 10.8507
which means that the DIVINT field of the UARTIBRD register (see page 243) should be set to 10.
The value to be loaded into the UARTFBRD register (see page 244) is calculated by the equation:
UARTFBRD[DIVFRAC] = integer(0.8507 * 64 + 0.5) = 54
With the BRD values in hand, the UART configuration is written to the module in the following
order:
1. Disable the UART by clearing the UARTEN bit in the UARTCTL register.
2. Write the integer portion of the BRD to the UARTIBRD register.
购买、咨询产品请填写询价信息:(3分钟左右您将得到回复)
询价型号*数量*批号封装品牌其它要求
删除
删除
删除
删除
删除
增加行数
  •  公司名:
  • *联系人:
  • *邮箱:
  • *电话:
  •  QQ:
  •  微信:

  • 关注官方微信

  • 联系我们
  • 电话:13714778017
  • 周一至周六:9:00-:18:00
  • 在线客服:

天天IC网由深圳市四方好讯科技有限公司独家运营

天天IC网 ( www.ttic.cc ) 版权所有©2014-2023 粤ICP备15059004号

因腾讯功能限制,可能无法唤起QQ临时会话,(点此复制QQ,添加好友),建议您使用TT在线询价。

继续唤起QQ 打开TT询价