• 当前位置:
  • 首页
  • >
  • PDF资料
  • >
  • AFS1500-2FGG256PP PDF文件及第244页内容在线浏览

AFS1500-2FGG256PP

AFS1500-2FGG256PP首页预览图
型号: AFS1500-2FGG256PP
PDF文件:
  • AFS1500-2FGG256PP PDF文件
  • AFS1500-2FGG256PP PDF在线浏览
功能描述: Fusion Family of Mixed Signal FPGAs
PDF文件大小: 18780.44 Kbytes
PDF页数: 共334页
制造商: MICROSEMI[Microsemi Corporation]
制造商LOGO: MICROSEMI[Microsemi Corporation] LOGO
制造商网址: http://www.microsemi.com
捡单宝AFS1500-2FGG256PP
PDF页面索引
[1] 页[2] 页[3] 页[4] 页[5] 页[6] 页[7] 页[8] 页[9] 页[10] 页[11] 页[12] 页[13] 页[14] 页[15] 页[16] 页[17] 页[18] 页[19] 页[20] 页[21] 页[22] 页[23] 页[24] 页[25] 页[26] 页[27] 页[28] 页[29] 页[30] 页[31] 页[32] 页[33] 页[34] 页[35] 页[36] 页[37] 页[38] 页[39] 页[40] 页[41] 页[42] 页[43] 页[44] 页[45] 页[46] 页[47] 页[48] 页[49] 页[50] 页[51] 页[52] 页[53] 页[54] 页[55] 页[56] 页[57] 页[58] 页[59] 页[60] 页[61] 页[62] 页[63] 页[64] 页[65] 页[66] 页[67] 页[68] 页[69] 页[70] 页[71] 页[72] 页[73] 页[74] 页[75] 页[76] 页[77] 页[78] 页[79] 页[80] 页[81] 页[82] 页[83] 页[84] 页[85] 页[86] 页[87] 页[88] 页[89] 页[90] 页[91] 页[92] 页[93] 页[94] 页[95] 页[96] 页[97] 页[98] 页[99] 页[100] 页[101] 页[102] 页[103] 页[104] 页[105] 页[106] 页[107] 页[108] 页[109] 页[110] 页[111] 页[112] 页[113] 页[114] 页[115] 页[116] 页[117] 页[118] 页[119] 页[120] 页[121] 页[122] 页[123] 页[124] 页[125] 页[126] 页[127] 页[128] 页[129] 页[130] 页[131] 页[132] 页[133] 页[134] 页[135] 页[136] 页[137] 页[138] 页[139] 页[140] 页[141] 页[142] 页[143] 页[144] 页[145] 页[146] 页[147] 页[148] 页[149] 页[150] 页[151] 页[152] 页[153] 页[154] 页[155] 页[156] 页[157] 页[158] 页[159] 页[160] 页[161] 页[162] 页[163] 页[164] 页[165] 页[166] 页[167] 页[168] 页[169] 页[170] 页[171] 页[172] 页[173] 页[174] 页[175] 页[176] 页[177] 页[178] 页[179] 页[180] 页[181] 页[182] 页[183] 页[184] 页[185] 页[186] 页[187] 页[188] 页[189] 页[190] 页[191] 页[192] 页[193] 页[194] 页[195] 页[196] 页[197] 页[198] 页[199] 页[200] 页[201] 页[202] 页[203] 页[204] 页[205] 页[206] 页[207] 页[208] 页[209] 页[210] 页[211] 页[212] 页[213] 页[214] 页[215] 页[216] 页[217] 页[218] 页[219] 页[220] 页[221] 页[222] 页[223] 页[224] 页[225] 页[226] 页[227] 页[228] 页[229] 页[230] 页[231] 页[232] 页[233] 页[234] 页[235] 页[236] 页[237] 页[238] 页[239] 页[240] 页[241] 页[242] 页[243] 页[244] 页[245] 页[246] 页[247] 页[248] 页[249] 页[250] 页[251] 页[252] 页[253] 页[254] 页[255] 页[256] 页[257] 页[258] 页[259] 页[260] 页[261] 页[262] 页[263] 页[264] 页[265] 页[266] 页[267] 页[268] 页[269] 页[270] 页[271] 页[272] 页[273] 页[274] 页[275] 页[276] 页[277] 页[278] 页[279] 页[280] 页[281] 页[282] 页[283] 页[284] 页[285] 页[286] 页[287] 页[288] 页[289] 页[290] 页[291] 页[292] 页[293] 页[294] 页[295] 页[296] 页[297] 页[298] 页[299] 页[300] 页[301] 页[302] 页[303] 页[304] 页[305] 页[306] 页[307] 页[308] 页[309] 页[310] 页[311] 页[312] 页[313] 页[314] 页[315] 页[316] 页[317] 页[318] 页[319] 页[320] 页[321] 页[322] 页[323] 页[324] 页[325] 页[326] 页[327] 页[328] 页[329] 页[330] 页[331] 页[332] 页[333] 页[334] 页
120%
Device Architecture
2-228 Revision 4
User-Defined Supply Pins
VREF I/O Voltage Reference
Reference voltage for I/O minibanks. Both AFS600 and AFS1500 (north bank only) support Microsemi
Pro I/O. These I/O banks support voltage reference standard I/O. The VREF pins are configured by the
user from regular I/Os, and any I/O in a bank, except JTAG I/Os, can be designated as the voltage
reference I/O. Only certain I/O standards require a voltage reference—HSTL (I) and (II), SSTL2 (I) and
(II), SSTL3 (I) and (II), and GTL/GTL+. One VREF pin can support the number of I/Os available in its
minibank.
VAREF Analog Reference Voltage
The Fusion device can be configured to generate a 2.56 V internal reference voltage that can be used by
the ADC. While using the internal reference, the reference voltage is output on the VAREF pin for use as
a system reference. If a different reference voltage is required, it can be supplied by an external source
and applied to this pin. The valid range of values that can be supplied to the ADC is 1.0 V to 3.3 V. When
VAREF is internally generated by the Fusion device, a bypass capacitor must be connected from this pin
to ground. The value of the bypass capacitor should be between 3.3 µF and 22 µF, which is based on the
needs of the individual designs. The choice of the capacitor value has an impact on the settling time it
takes the VAREF signal to reach the required specification of 2.56 V to initiate valid conversions by the
ADC. If the lower capacitor value is chosen, the settling time required for VAREF to achieve 2.56 V will
be shorter than when selecting the larger capacitor value. The above range of capacitor values supports
the accuracy specification of the ADC, which is detailed in the datasheet. Designers choosing the smaller
capacitor value will not obtain as much margin in the accuracy as that achieved with a larger capacitor
value. Depending on the capacitor value selected in the Analog System Builder, a tool in Libero SoC, an
automatic delay circuit will be generated using logic tiles available within the FPGA to ensure that VAREF
has achieved the 2.56 V value. Microsemi recommends customers use 10 µF as the value of the bypass
capacitor. Designers choosing to use an external VAREF need to ensure that a stable and clean VAREF
source is supplied to the VAREF pin before initiating conversions by the ADC. Designers should also
make sure that the ADCRESET signal is deasserted before initiating valid conversions.
2
If the user connects VAREF to external 3.3 V on their board, the internal VAREF driving OpAmp tries to
bring the pin down to the nominal 2.56 V until the device is programmed and up/functional. Under this
scenario, it is recommended to connect an external 3.3 V supply through a ~1 KOhm resistor to limit
current, along with placing a 10-100nF capacitor between VAREF and GNDA.
User Pins
I/O User Input/Output
The I/O pin functions as an input, output, tristate, or bidirectional buffer. Input and output signal levels are
compatible with the I/O standard selected. Unused I/O pins are configured as inputs with pull-up
resistors.
During programming, I/Os become tristated and weakly pulled up to VCCI. With the VCCI and VCC
supplies continuously powered up, when the device transitions from programming to operating mode, the
I/Os get instantly configured to the desired user configuration.
Unused I/Os are configured as follows:
Output buffer is disabled (with tristate value of high impedance)
Input buffer is disabled (with tristate value of high impedance)
Weak pull-up is programmed
Axy Analog Input/Output
Analog I/O pin, where x is the analog pad type (C = current pad, G = Gate driver pad, T = Temperature
pad, V = Voltage pad) and y is the Analog Quad number (0 to 9). There is a minimum 1 M to ground on
AV, AC, and AT. This pin can be left floating when it is unused.
2. The ADC is functional with an external reference down to 1V, however to meet the performance parameters highlighted in the
datasheet refer to the VAREF specification in Table 3-2 on page 3-3.
购买、咨询产品请填写询价信息:(3分钟左右您将得到回复)
询价型号*数量*批号封装品牌其它要求
删除
删除
删除
删除
删除
增加行数
  •  公司名:
  • *联系人:
  • *邮箱:
  • *电话:
  •  QQ:
  •  微信:

  • 关注官方微信

  • 联系我们
  • 电话:13714778017
  • 周一至周六:9:00-:18:00
  • 在线客服:

天天IC网由深圳市四方好讯科技有限公司独家运营

天天IC网 ( www.ttic.cc ) 版权所有©2014-2023 粤ICP备15059004号

因腾讯功能限制,可能无法唤起QQ临时会话,(点此复制QQ,添加好友),建议您使用TT在线询价。

继续唤起QQ 打开TT询价