ProASIC3 DC and Switching Characteristics
2-46 Revision 13
2.5 V LVCMOS
Low-Voltage CMOS for 2.5 V is an extension of the LVCMOS standard (JESD8-5) used for general-
purpose 2.5 V applications.
Table 2-56 • Minimum and Maximum DC Input and Output Levels
Applicable to Advanced I/O Banks
2.5 V LVCMOS VIL VIH VOL VOH IOL IOH IOSL IOSH IIL1 IIH
2
Drive Strength
Min.
V
Max.
V
Min.
V
Max.
V
Max.
V
Min.
VmAmA
Max.
mA
3
Max.
mA
3
µA
4
µA
4
2 mA –0.3 0.7 1.7 2.7 0.7 1.7 2 2 18 16 10 10
4 mA –0.3 0.7 1.7 2.7 0.7 1.7 4 4 18 16 10 10
6 mA –0.3 0.7 1.7 2.7 0.7 1.7 6 6 37 32 10 10
8 mA –0.3 0.7 1.7 2.7 0.7 1.7 8 8 37 32 10 10
12 mA –0.3 0.7 1.7 2.7 0.7 1.7 12 12 74 65 10 10
16 mA –0.3 0.7 1.7 2.7 0.7 1.7 16 16 87 83 10 10
24 mA –0.3 0.7 1.7 2.7 0.7 1.7 24 24 124 169 10 10
Notes:
1. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL.
2. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is
larger when operating outside recommended ranges
3. Currents are measured at high temperature (100°C junction temperature) and maximum voltage.
4. Currents are measured at 85°C junction temperature.
5. Software default selection highlighted in gray.
Table 2-57 • Minimum and Maximum DC Input and Output Levels
Applicable to Standard Plus I/O Banks
2.5 V LVCMOS VIL VIH VOL VOH IOL IOH IOSL IOSH IIL
1
IIH
2
Drive Strength
Min.
V
Max.
V
Min.
V
Max.
V
Max.
V
Min.
VmAmA
Max.
mA
3
Max.
mA
3
µA
4
µA
4
2 mA –0.3 0.7 1.7 2.7 0.7 1.7 2 2 18 16 10 10
4 mA –0.3 0.7 1.7 2.7 0.7 1.7 4 4 18 16 10 10
6 mA –0.3 0.7 1.7 2.7 0.7 1.7 6 6 37 32 10 10
8 mA –0.3 0.7 1.7 2.7 0.7 1.7 8 8 37 32 10 10
12 mA –0.3 0.7 1.7 2.7 0.7 1.7 12 12 74 65 10 10
Notes:
1. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL.
2. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is
larger when operating outside recommended ranges
3. Currents are measured at high temperature (100°C junction temperature) and maximum voltage.
4. Currents are measured at 85°C junction temperature.
5. Software default selection highlighted in gray.