• 当前位置:
  • 首页
  • >
  • PDF资料
  • >
  • 5962G8957701QZC PDF文件及第13页内容在线浏览

5962G8957701QZC

5962G8957701QZC首页预览图
型号: 5962G8957701QZC
PDF文件:
  • 5962G8957701QZC PDF文件
  • 5962G8957701QZC PDF在线浏览
功能描述: BCRTM
PDF文件大小: 2024.39 Kbytes
PDF页数: 共61页
制造商: ETC1[List of Unclassifed Manufacturers]
制造商LOGO: ETC1[List of Unclassifed Manufacturers] LOGO
制造商网址:
捡单宝5962G8957701QZC
PDF页面索引
120%
BCRTM-13
#1 Status Register (Read Only)
These bits indicate the BCRTM’s current status.
Bit
Number Description
BIT 15 TEST. This bit reflects the inverse of the TEST output. It changes state simultaneously with the TEST output.
BIT 14 (RT,M) Remote Terminal (or Monitor) Active. Indicates that the BCRTM, in the Remote Terminal (or Monitor)
mode, is presently servicing a command. This bit reflects the inverse of the COMSTR pin.
BIT 13 (RT) Dynamic Bus Control Acceptance. This bit reflects the state of the Dynamic Bus Control
Acceptance bit in the RT status word (see Register 10 on page 16).
BIT 12 (RT) Terminal Flag bit is set in RT status word. This bit reflects the result of writing to Register 10, bit 11
BIT 11 (RT) Service Request bit is set in RT status word.This bit reflects the result of writing to Register 10, bit 10.
BIT 10 (RT) Busy bit is set in RT status word.This bit reflects the result of writing to Register 10, bits 9 or 14.
BIT 9 BIT is in progress.
BIT 8 Reset is in progress. This bit indicates that either a write to Register 12 has just occurred or the BCRTM has
just received a Reset Remote Terminal (#01000) Mode Code. This bit remains set less than 1ms.
BIT 7 BC/(RT) Mode. Indicates the current mode of operation. A reset operation must be performed when changing
between BC and RT modes.
BIT 6 Channel A/B. Indicates either the channel presently in use or the last channel used.
BIT 5 Subsystem Fail Indicator. Indicates receiving a subsystem fail signal from the host subsystem on the
SSYSF input.
BITs 4-1 Reserved.
BIT 0 (BC) Command Block Execution is in progress. (RT) Remote Terminal is in operation. This bit reflects bit 0 of
Register 0.
#2 Current Command Block Register (BC,M)/Remote Terminal Descriptor Space Address Register (RT)
(BC) This register contains the address of the head pointer of the Command Block being executed. Accessing a new Command
Block updates it.
(RT) The host CPU initializes this register to indicate the starting location of the RT Descriptor Space. The host must allocate
320 sequential locations following this starting address. For proper operation, this location must start on an I x 512 decimal
address boundary, where I is an integer multiple.
(M) This register contains the address of the control/status word of the current Monitor Command Block. Accessing a new
Command Block updates it.
#3 Polling Compare Register
In the polling mode, the CPU sets the Polling Compare Register to indicate the RT response word on which the BCRTM should
interrupt. This register is 11 bits wide, corresponding to bit times 9 through 19 of the RT’s 1553 status word response. The
sync, Remote Terminal Address, and parity bits are not included (see the section on Polling, page 32).
购买、咨询产品请填写询价信息:(3分钟左右您将得到回复)
询价型号*数量*批号封装品牌其它要求
删除
删除
删除
删除
删除
增加行数
  •  公司名:
  • *联系人:
  • *邮箱:
  • *电话:
  •  QQ:
  •  微信:

  • 关注官方微信

  • 联系我们
  • 电话:13714778017
  • 周一至周六:9:00-:18:00
  • 在线客服:

天天IC网由深圳市四方好讯科技有限公司独家运营

天天IC网 ( www.ttic.cc ) 版权所有©2014-2023 粤ICP备15059004号

因腾讯功能限制,可能无法唤起QQ临时会话,(点此复制QQ,添加好友),建议您使用TT在线询价。

继续唤起QQ 打开TT询价