• 当前位置:
  • 首页
  • >
  • PDF资料
  • >
  • 162GB31T1608SY714 PDF文件及第31页内容在线浏览

162GB31T1608SY714

162GB31T1608SY714首页预览图
型号: 162GB31T1608SY714
PDF文件:
  • 162GB31T1608SY714 PDF文件
  • 162GB31T1608SY714 PDF在线浏览
功能描述: 环形MIL规格连接器
PDF文件大小: 1.70 Mbytes
PDF页数: 共41页
制造商: Amphenol Pcd
制造商LOGO: Amphenol Pcd LOGO
制造商网址: http://www.amphenol.com
捡单宝162GB31T1608SY714
PDF页面索引
120%
31
Interconnection Accessories
INSTALLATION - PROCEDURE
Prepare the cable making sure that a sufficient length of shield is available, so that it fits against the front shoulder of the lip groove.
Before insertion of connector contacts, slide the heat-shrinkable connector boot onto the cable followed by the Spring Adapter.
Position the heatshrinkable boot, Spring Adapter, and shield braid out of the way and insert the connector contacts.
Depending upon the shielding braid size, it can either be folded back onto itself or bunched up concertina style out of the way
for easy access to the cable conductors.
Screw the Spring Adapter onto the connector and tighten to the torque value specified by the connector manufacturer. Typical
torque values are shown in table on Page 7. It is recommended that the connector threads are lubricated with a suitable
compound if a liquid thread lock is not used. The adapter should be hand tightened to ensure proper thread alignment and
then tightened with a strap wrench and torque meter to the specified torque.
Bring the cable shield braid up onto the adapter body so that it fits against the front shoulder of the lip groove. Alternatively
extend the braid past the lip groove.
NOTE: After assembly, braid can be trimmed with side cutters
or folded back and secured with high temperature tape
Open up the constant force spring and wrap it around the cable braid section that is positioned over the constant force spring
slot area of the adapter. This is most easily accomplished by lifting up the end of the spring and trapping the braid covered
adapter between the spring coil and raised end. The spring will now stay in place and can be installed by simply rolling the
coil around the braid covered adapter. Refer to appropriate code of practice for procedure to install heatshrink shape.
Lift Up End of Spring
Trap Braid Covered Adapter
between Spring Coil and raised
end
Roll Spring Coil around
Adapter
Secure Cable Braid
End with Tape
Fold Cable Braid back
购买、咨询产品请填写询价信息:(3分钟左右您将得到回复)
询价型号*数量*批号封装品牌其它要求
删除
删除
删除
删除
删除
增加行数
  •  公司名:
  • *联系人:
  • *邮箱:
  • *电话:
  •  QQ:
  •  微信:

  • 关注官方微信

  • 联系我们
  • 电话:13714778017
  • 周一至周六:9:00-:18:00
  • 在线客服:

天天IC网由深圳市四方好讯科技有限公司独家运营

天天IC网 ( www.ttic.cc ) 版权所有©2014-2023 粤ICP备15059004号

因腾讯功能限制,可能无法唤起QQ临时会话,(点此复制QQ,添加好友),建议您使用TT在线询价。

继续唤起QQ 打开TT询价