http://www.m-system.co.jp/ 10BXC SPECIFICATIONS ES-0893 Rev.12 Page 1/7
High-density Signal Conditioners 10-RACK
STANDARD RACK
Functions & Features
• Standard 19" rack for 10-RACK signal conditioners
• Line power supplied via the rear rack bus
• Dual-redundant power supply or two independent power
sources selectable with AC power supply
• Supply pressure at manifold plug
• Direct interface to various DCS with the rack connector
MODEL: 10BXC-[1][2]-[3][4]
ORDERING INFORMATION
• Code number: 10BXC-[1][2]-[3][4]
Specify a code from below for each [1] through [4].
(e.g. 10BXC-12-K2/Q)
• Specify the specification for option code /Q
(e.g. /C01)
[1] FUNCTION
1: Power distribution
2: Power distribution & pressure supply
[2] CONNECTOR
0: None
1: Fujitsu FCN type I/O connector
2: Yokogawa DCS connector (MAC2 dual redundant system use)
3: Nippon Shokubai DCS connector
4: Azbil DCS AI connector
5: Azbil DCS AO connector
6: Azbil DCS AI connector (ELCO connector)
7: Azbil DCS AO connector (ELCO connector)
8: Yokogawa DCS connector (VMx/PM1 dual redundant system use)
E3: Toshiba DCS SAIN1 card use
(Panasonic AXM220001 used)
(DISCONTINUED; replace with code "E3A".)
E3A: Toshiba DCS SAIN1 card supported
(Omron XG4A-2031 used)
H1: Hitachi DCS connector
H2: Hitachi DCS EX-CDL cable connector
M-System guarantees the connecting section.
[3] POWER SUPPLY UNIT
AC Power
K: 85 – 132 V AC; single power source
(Operational voltage range 85 – 132 V, 47 – 63 Hz)
K2: 85 – 132 V AC; dual-redundant power supply
(Operational voltage range 85 – 132 V, 47 – 63 Hz)
KK: 85 – 132 V AC; two independent power sources
(Operational voltage range 85 – 132 V, 47 – 63 Hz)
L: 170 – 264 V AC; single power source
(Operational voltage range 170 – 264 V, 47 – 63 Hz)
L2: 170 – 264 V AC; dual-redundant power supply
(Operational voltage range 170 – 264 V, 47 - 63 Hz)
DC Power
R: 24 V DC; no power supply unit
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
AC/DC Power
KR: 85 – 132 V AC / 24 V DC; two independent power sources
(85 – 132 V, 47 – 63 Hz or 24V ±10 %, ripple 10 %p-p max.)
(Redundant or independent power sources are
recommended for long time use without interruption.)
[4] OPTIONS
blank: none
/Q: With options (specify the specification)
SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
Power supply and signal conditioner side of the main PWB are not coated.
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating
RELATED PRODUCTS
• Blank filler plate (model: P-101)
• Connector terminal block (model: CNT)
• Special cable with 40-pin connector (model: FCN)
GENERAL SPECIFICATIONS
Construction: Metal plates assembly
Capacity: 16 positions
Connection
Power input: M4 screw terminals (torque 0.8 N·m)
Power alarm: M4 screw terminals (torque 0.8 N·m)
Pneumatic: Rc 3/8" female (torque ≤ 12 N·m)
Screw terminal: Nickel-plated brass
Manifold: Aluminium alloy
Isolation: I/O connector to alarm output to power to FG
Power alarm output: N.C. contact turns off at power failure
or failure of power units. Supplied only with dual-redundant
power supply or two independent power sources
